N SPORT Seat rail Products
N SPORT S6
Side 6 Position
N SPORT S6 Side-mount 6-position Seat Rail
Side-mount seat rail with 6 height settings at rear of seat
- Designed for full bucket seats and other side-mount seats.
- Height adjustments can be made with the side stays and with the 6-step height adjustments at the rear of the seat.
- The general-purpose side stays accommodate many seat models.
- Designed with an adjustable seat angle to accommodate vehicles with certain floor configurations that result in a steeply reclined seat and a seat surface that is too high in the front, thus preventing the driver from fully depressing the pedals.
- Distortion of sliders due to welding heat is eliminated, resulting in smoother sliding action. The sliders and mounting frame are secured with rivets. The sliders and seat belt buckle stay are secured with rivets.
Smooth sliding is assured.
Height adjustments are provided on the side stays and the 6-step height adjustment at the rear of the seat.
In addition to the height adjustments on the side stays, the rear of the seat can be adjusted to six different height settings (2 × 3) through combinations of the two bolt holes provided at the rear of the frame fixed to the sliders and three bolt holes at the rear of the mounting frame.
Because height adjustments can be made with the side bolts, no extra load is applied to the sliders even when the front and rear are set to different heights. The sliders and seat angle can be set to six possible combinations without affecting the smoothness of the sliding action.
The general-purpose side stays accommodate many seat models.
The bolt holes used for mounting the seat itself are cut into elongated and diagonal shapes. In addition, the bolt holes for attaching to the sliders are elongated, which allows for mounting of many seat models. Moreover, in addition to offering fine adjustment of seat height and seat angle, this seat rail provides lateral seat adjustment to the left and right. It is also compatible with seats with a high bolt-hole mounting position,* such as the Recaro RS-G. In addition, weight-relief holes are provided for maximum weight reduction.
* For seats with higher mounting positions at the rear, only the bolt holes at the top of the side stays can be used.
Includes seat-mounting bolts.
All bolts required to mount the seat are included. Your current seat can be mounted only with these bolts.
Includes side airbag canceller.
Regardless of whether standard or optional equipment is installed, side airbag cancellers are provided to prevent the triggering of warning lights in models equipped with side airbags.
- Seat drop:
10–30 mm for Standard model
- Installation method:
- Height adjustments:
On side stays plus 6-step adjustment provided at rear of seat
Slider adjustments: 18 mm/step
Mounting frame adjustments: 12 mm/step
Seat angle adjustment: 0°–8°
- Mounted size:
290 (±5) from front to rear of side stay × 355–450 mm left to right
260 (±5) from front to rear of side stay × 355–450 mm left to right
233 (±5) from front to rear of side stay × 355–450 mm left to right
- Parts supplied:
Seat belt buckle relocation parts*1
Side airbag canceller*2
*1 Included with models requiring relocation of seat belt buckle.The contents of parts vary depending on the model.
*2 Supplied with models equipped with side airbags.
Tips for mounting the seat to the side stays
Mount the seat to the side stays as orientated in the illustrations below. The installation width of the seat to be installed determines the orientation.
Adjustments required to center the seat relative to the steering wheel (adjusting the seat to the left or right) are performed by changing the orientation of the side stays as they mount to the seat rails.
Use spacers if the grommets of the belt holes interfere with the side stays, creating a gap between the seat body and the side stays.
(Adjust the number of spacers to fill the gap.)
Even if no interference occurs, a gap may be present depending on the width of the seat to be mounted. In that case, use spacers as well. (Use 30-mm bolts when using spacers; use 20-mm bolts when not using spacers.)
Note: Various spacers and bolts are included with the seat rail.
Compatible Auto Makers and Compatible Seats
PRO RACER SP series
|All models of full bucket seats*2||031|
PRO ADV series
|All models of full bucket seats|
*1 Only the bolt holes at the top of the side stays can be used at the rear of the seat.
*2 Not compatible with Zodia model.
*3 Not compatible with ADV XT model.
Accommodates seats with an installation width of 355 to 450 mm apart from those listed above.
“Seat mounting width” explained
We suggest measuring the width of the seat across its bottom as shown in the image. Measure from the surfaces that mount to the side stays.
If the front and rear of the seat vary in width, measure the seat at its widest point.