N SPORT Seat rail Products
N SPORT SSD-V
Side Super Down VERTICAL
Features
N SPORT SSD-V Side-mount Super-low-profile Seat Rail with Vertically Oriented Sliders
A side-mount Super-low-profile seat rail with vertically oriented sliders
- Designed for full bucket seats and other side-mount seats.
- Height adjustments can be made only with the side stays.
- Designed for vehicle floors with little space to spare.
- The seat drops down between the sliders, bringing it to the lowest position physically possible.
- Vertically oriented double-lock sliders.
- Side stays accommodate many seat models.
- Includes anchor stays for attaching a 4-point harness.
- Distortion of sliders due to welding heat is eliminated, resulting in smoother sliding action. The sliders and mounting frame are secured with bolts. The seat belt buckle is integrated into the side stay.
Detail
Smooth sliding is assured.
Welding heat is the primary cause of slider hardening. The mounting frame and sliders of this model are secured with bolts to prevent thermal distortion of the metal sliders (sliders and side stays, which is difficult with vertically oriented sliders) from welding. Smoother sliding action is achieved by the elimination of distortion due to welding heat.
Double lock with vertically oriented sliders and drop-in type
Thanks to the vertically oriented slides, it is possible to use the drop-in method to mount it in the floor of a vehicle with limited space, such as a roadster. The seat can be lowered almost to the vehicle floor*1. While the drop-in type incorporates a vertically oriented slider, it features a double lock*2 thanks to locking mechanisms provided on both the left and right sliders. Moreover, the integration of the seat belt buckle and side stay reduces the overhang on the console side and keeps the steering wheel as close to the center as possible.
*1 The mounting position of the seat varies depending on the position of the bolt holes.
*2 Note that, because limited space is available for the locking mechanism in some vehicle models, the console-side slide lever may be difficult to manipulate.
Side stays accommodate many seat models.
Thanks to the long diagonal bolt holes provided for mounting the seat, many seat models can be accommodated and fine adjustments of the seat height and seat angle are possible. This design also supports seats with high mounting positions* (bolt hole positions) such as the Recaro RS-G.
* For seats with higher mounting positions at the rear, only the bolt holes at the top of the side stays can be used.
Includes seat-mounting bolts.
All bolts required to mount the seat are included. Your current seat can be mounted only with these bolts.
Can be fitted with anchor stays for installing a four-point harness.
Anchor stays for a four-point harness,* which is highly convenient for two-seater vehicles, can be installed. These anchor stays feature a special reinforcing plate.
* The anchor (eye) bolt is not included. Some vehicles may lack sufficient space on the vehicle floor to accept this addition.
side airbag canceller.
Vehicles equipped with side airbags require a separate side airbag canceller to prevent warning lights from illuminating. There are 6 types, NPC001~006. Please check the matching list for the appropriate product.
Specification
- Seat drop: 40–50 mm
- Installation method: Side mount
- Height adjustment: Can be made only with side stays. Side stay adjustments: 17 mm/step
- Mounted size: 290 mm (±10) from front to rear of side stay × 395 mm left to right3*2
- Parts supplied: Seat-mounting bolts Seat belt buckle relocation parts*1
*1 Included with models requiring relocation of seat belt buckle.The contents of parts vary depending on the model.
*2 Accommodates seats of up to 395 mm, but since the side stay is not movable, a spacer is required for the gap.
Installation example of nd5rc
Conform
Compatible Auto Makers and Compatible Seats
 |  |  |  |  |  |  |
| RS-G series*1 TS-G series*1 SP-G series SP-GT series SP-A、 PRO RACER SP series | All models of full bucket seats*2 | 031 042 067 | REV series*4 | IMOLA2 | HTE-ONE*1*3 PROTOTIPO*1*3 ARS*1*3 | All models of full bucket seats |
*1 Only the bolt holes at the top of the side stays can be used at the rear of the seat.
*2 Not compatible with Zodia or Zeta3 Type XL models.
*3 Not compatible with seat widths exceeding 395 mm.
*4 Not compatible with Model REV2 made after 2016 (because the mounting width is 430 mm).
Accommodates seats with an installation width of up to 395 mm apart from those listed above.
“Seat mounting width” explained
We suggest measuring the width of the seat across its bottom as shown in the image. Measure from the surfaces that mount to the side stays.
If the front and rear of the seat vary in width, measure the seat at its widest point.
